Standard Motor Catalog

Section TR Technical Reference Guide

DUTY CYCLES PER IEC Standardized coded duty cycles for use of purchaser to define the expected or any equivalent loading condition, and which may be used by the manufacturer in defining the rating. The basic duty types are: S1- Continuous running duty S2- Short time Duty S3- Intermittent periodic duty S4- Intermittent periodic duty with starting S5- Intermittent periodic duty with electric braking S6- Continuous operation periodic duty S7- Continuous operation periodic duty with electric braking. S8- Continuous operation periodic duty with related load / speed changes S9- Duty with one-periodic load and speed variations S10- Duty with not more than 4 discreet values STARTING LOAD INERTIA (WK²) In any type of duty cycle operation, it is necessary to determine not only the horsepower requirements but the number of times the motor will be started, the inertia of the driven machine, the type of load (constant or variable torque) and the method of stopping the motor. The inertia (WK²) of the rotating parts of the driven equipment affects the acceleration time and motor heating during acceleration. The heating of motor rotor and stator during frequent starting, stopping, and /or reversals can become a design limitation. If the motor is direct connected, the inertia supplied by the equipment manufacturer may be used as is. If the motor is to drive the equipment through a pulley or gear such that the driven equipment is operating at a higher or lower speed than the motor, it is necessary to calculate the inertia referred to the motor shaft: that is, an equivalent inertia based on the speed of the motor. The method of stopping the motor is also taken into consideration in a duty cycle calculation. For example, if the motor is allowed to coast to a stop or mechanical braking is used; the RMS horsepower calculation may be affected. Plug stopping DC braking increases motor heating considerably. Therefore, the method of stopping must be part of the duty cycle data provided. STARTING FREQUENCY A special kind of duty cycle is one in which a motor is required to perform repetitive starts with a given load and connected inertia. Motor selection must take into account the motor heating caused by starting frequency, load inertia and running load. WK² (Driven Equipment) x RPM² (Driven Equipment) RPM² (Motor)

A motor during acceleration draws about 6 times full-load current, so resistance losses during starting are up to 36 times (current squared) the losses at full-load. A motor operating on a low inertia load (pump) may come up to speed vary quickly, in less than one second. Starting losses may be so low that the start cycle could repeated several times per minute without overheating the winding. However, motor life can be limited by mechanical starting stresses. When frequent starting is planned refer to NEMA MG-10. HIGH INERTIA LOADS At the other extreme, the same motor connected to a high inertia load (such as a large centrifugal blower) could burn out before getting up to full speed on the first start. Motor applications involving frequent starts or high load inertia must be carefully studied to obtain satisfactory operation and long motor life. The following table lists recommended maximum load inertias for type K, KB, KG, KS and KGS, KBS 60 HZ or 50 HZ, motor starting a fan or centrifugal pump load for two successive cold starts or one start from rated load temperature. The cold stars should be possible within 10 seconds of each other at rated frequency and voltage, and permitted by conventional control. It is recommended, however, that high inertia drives have thermal protection in the motor to prevent burnout from misapplication or excessive starting frequency. Table 16: Maximum load Inertia NEMA MG-1, parts 12 and 20 Speed, RPM Hp 3600 1800 1200 900 720 600 514 Load WK² (Exclusive of Motor WK²) lb - ft² 1 - 5.8 15 31 53 82 118 1.5 1.8 8.6 23 45 77 120 174 2 2.4 11 30 60 102 158 228 3 3.5 17 44 87 149 231 335 5 5.7 27 71 148 242 375 544 7.5 8.3 39 104 208 256 551 798 10 11 51 137 273 467 723 1048 15 16 75 200 400 684 1060 1540 20 21 99 262 525 898 1393 2018 25 26 122 324 647 1108 1719 2491 30 31 144 384 769 1316 2042 2959 40 40 189 503 1007 1725 2677 3881 50 49 232 620 1241 2127 3302 4788 60 58 275 735 1473 2524 3819 5680 75 71 338 904 1814 3111 4831 7010 100 92 441 1181 2372 4070 6320 9180 125 113 542 1452 2919 5010 7790 11310 150 133 640 1719 3456 5940 9230 - 200 172 831 2238 4508 77050 12060 - 250 210 1017 2744 5540 9530 14830 - 300 246 1197 3239 6540 11270 - - 350 281 1373 3723 7530 - - - 400 315 1546 4199 8500 - - - 450 349 1714 4666 9460 - - - 500 381 1880 5130 - - - - 600 443 2202 6030 - - - - 700 503 2514 - - - - - 800 560 2815 - - - - -

TECHNICAL REFERENCE GUIDE WK² (Referred to Motor Shaft) =

TR.18

Data subject to change without notice. 03/24 • www.wolongamerica.com

Made with FlippingBook flipbook maker